Forward Controls Design

-12%
Add to compare

Forward Controls Design RHF M-LOK Handguard – 9.5″

Out of stock

Original price was: $195.00.Current price is: $171.59.

RHF (Railed Handguard, Forward Controls) is based on the superb CMT UHPR Mod2, with full-length 1913 rails at 12 o’clock, and MLOK at 3, 6, and 9 o’clock.

  • Machined from 6000 series extruded aluminum.
  • Barrel nut machined from 7075 aluminum.
  • Type 3 anodized
  • Weight: 9.02oz
  • Barrel nut torque: milspec 40-70ft/lbs.
  • Rail clamp screws torque: 45 inc/lbs.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design Pivot and Takedown Pins

Out of stock

Original price was: $35.00.Current price is: $33.25.

PF-040 (Pins, Forward Controls, 0.040) is a set of elegantly simple, and superbly crafted AR15/M16 pivot and takedown pins.

  • Machined from 17-4 PH SS bar stock
  • QPQ finished
  • Made in the USA
View product
-12%
Add to compare

Forward Controls Design JCW Joint Castle Nut Wrench

Out of stock

Original price was: $35.00.Current price is: $30.73.

JCW (Joint Castle nut Wrench) is a dedicated, heavy-duty twin castle nut wrench.

  • Machined from 4140 steel
  • Heat-treated
  • Black oxide finish
  • 3.14 oz
  • Torque value is 38 to 42 ft-lb
Select options This product has multiple variants. The options may be chosen on the product page
-6%
Add to compare

Forward Controls Design Trigger Guard – Winter

Out of stock

$23.41 – $23.75

TGF (Trigger Guard, Forward Controls) is designed for use with TDP spec forged lower receivers, and fills the gap forward of the pistol grip, between the trigger guard “ears”. The winter version has as much constant/unchanged space from the trigger bow forward as possible (instead of the space inside tapering and decreasing as the trigger guard nears the receiver’s front trigger guard holes).

  • Available in anodized black, desert tan, and OD green.
  • Lower receivers made from Cerro Forge “keyhole” forgings generally have taller trigger guard ears, as do Colt, LMT, and BCM lower receivers.
  • Please note ZEV produced lower receivers appear to have shorter trigger guard ears, and these shortened ears expose a bit of the bottom of the TGF, as shown below. This has no bearing on functionality. The latest Mega lowers (with the old Mega atomic whirl) has been reported to have long ears that do cover the TGF.
  • TGF is proudly designed and made in the USA. A trigger guard roll pin and set screw (for the front) are included. A 1/16 Allen wrench is required (not included).
  • TGF is machined from 7075 aluminum.
Select options This product has multiple variants. The options may be chosen on the product page
-4%
Add to compare

Forward Controls Design Glock MOS Mounting Plate for RMR/SRO

Out of stock

Original price was: $72.00.Current price is: $68.87.

OPF-G, RMR (Optics Platform, Glock, for RMR) is a Glock MOS Adapter Set 01 and Set 02 compatible plate for mounting Trijicon RMR or SRO on Glock Gen 4 and Gen 5 slides, G17, G19, G34, G35, G41 (width 25mm/1 inch.) and G40 that uses Set 02.

  • Sight is to be fully supported in the front and rear by recoil lugs/fences, with minimum movement.
  • Eliminate the need to use an additional sealer plate.
  • Correct length sight to plate, and plate to slide screws. Screws are to be Torx.
  • The adapter plate is to be machined in steel.
  • Proudly designed and made in the USA.
View product
-12%
Add to compare

Forward Controls Design JMW Joint Muzzle Device Wrench

Out of stock

Original price was: $35.00.Current price is: $30.73.

JMW is the newest addition to FCDs’ line of dedicated, high-quality AR15/M16 tools. It is a combination wrench with a 3/4 wrench with a 0.23 thickness for the A2 compensator, and another 3/4 wrench with a 0.20 thickness for the Keymo, Key Micro mounts, such as our 6315KM, 6310KM, SOLGW’s NOX, and Dead Air’s flash suppressors, compensators and brakes.

  • JMW is designed for muzzle devices with thinner than A2 compensator spec flats.
  • Billet machined in 4140.
  • Heat-treated, and black oxide.
  • Recommended torque value (20 to 30 ft/lb) is laser engraved.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design Stoner 63 Style Comp / Flash Hider – Keymo (1/2×28)

Out of stock

Original price was: $105.00.Current price is: $99.75.

6315KM is the Dead Air suppressor Keymo version mount of the 6315 (1/2×28) flash suppressor, compatible specifically with .223 Dead Air sound suppressors with Keymo interface.

  • Machined in 4140, heat-treated, and QPQ coated.
  • Length: 2.38″
  • Weight: 3.97oz
  • Drilled for pinning
  • Recommended torque: 25 ft-lbs +/- 5
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design 3P Comp/Flash Hider – A2 (1/2×28)

Out of stock

Original price was: $50.00.Current price is: $47.50.
View product
-15%
Add to compare

Forward Controls Design Low Drag Forward Assist – Dimpled

Out of stock

Original price was: $42.00.Current price is: $35.85.

Specifically designed and purpose-built for AR15s and M16s with ambidextrous charging handles, the LDFA is a snag-free, rimless forward assist with a small footprint. Both the LDFA and ABC/R designs are partially based on natural selection and mutation. As the AR and its manual of arms evolve, so should its controls.

  • CNC Billet construction, LDFA is machined from 4130 steel bar stock, heat treated with a black nitride finish.
  • The smaller footprint of the plunger face does not impact its usability.
  • Dimpled design.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design Low Drag Forward Assist – Serrated

Out of stock

Original price was: $42.00.Current price is: $39.99.

Specifically designed and purpose-built for AR15s and M16s with ambidextrous charging handles, the LDFA is a snag-free, rimless forward assist with a small footprint. Both the LDFA and ABC/R designs are partially based on natural selection and mutation. As the AR and its manual of arms evolve, so should its controls.

  • CNC Billet construction, LDFA is machined from 4130 steel bar stock, heat treated with a black nitride finish.
  • The smaller footprint of the plunger face does not impact its usability.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design GPT – Gas Tube Pin Tool

Out of stock

Original price was: $35.00.Current price is: $33.25.

GPT (Gas tube Pin Tool) is a jig tailor-made for installing and removing the gas tube roll pin on an AR15/M16 low-profile gas block. Machined in 6061 aluminum and Type III hard coat anodized, GPT makes installing the gas tube pin on a low profile gas block painless.

  • MAX gas block length: 1.00
  • MAX gas block height: 1.35
  • Compatible with most gas blocks including Modern Armory, our GBF (Gas Block, Forward Controls), BCM, Rainier, VLTOR, Knight’s Armament, Badger Ordnance, Daniel Defense, SLR, or other low profile gas blocks based on the original Crane design.
  • Known incompatible low profile gas blocks: Aero, Luth-AR, and DPMS, and adjustable gas blocks.
View product
-5%
Add to compare

Forward Controls Design .750 Gas Block

Out of stock

Original price was: $60.00.Current price is: $57.00.

GBF (Gas Block Forward Controls) is a 0.750 gas journal gas block done FCD way: meticulously designed and machined, with thoughtful features throughout.

  • Machined from heat-treated 4140 bar stock
  • GBF is manganese phosphate coated
  • GBF holds rather tight tolerances to squeeze every bit of tight seal we can from the design.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design Enhanced Ambi Mag Release – Extended, Serrated

Out of stock

Original price was: $70.00.Current price is: $66.50.

EMR-A is a long in development ambidextrous magazine release for .223 and .308 AR receivers. The placement of its lever is well thought out to closely mirror the magazine release button on the right side. The portion immediately below the bolt catch’s lower paddle has a lower profile to avoid interference, heretofore a common drawback of popular ambidextrous mag catches, it is also left smooth.

  • Made from CNC machined 4140 steel and Black Nitride coated
  • Lever 7075 aluminum and Type 3 hard coat anodized.
  • The roll pin has a shear strength of 800lbs.
View product
-5%
Add to compare

Forward Controls Design MSQ-H Rotation Limited M-LOK QD Sling Mount

Out of stock

Original price was: $33.50.Current price is: $31.82.

FCD’s MLOK QD swivel sling adapter is not unlike other MLOK sling adapters in the market, except MSQ-H (MLOK, Sling adapter, QD, Heavy) is billet machined in 4140, and black nitrided.

  • MSQ-H weighs in at 0.867oz. It’s not meant to be light, it is meant to be durable.
  • MSQ-H’s QD swivel socket is rotation limited, MLOK mounting hardware is included. As with all Forward Controls products, MSQ-H is proudly made in the USA.
  • An 8/32 Allen wrench (not included) is required to torque the mounting screws.
View product
-5%
Add to compare

Forward Controls Design ATA – Adjustable Turret Caps for Micro Series Sights

Out of stock

Original price was: $50.00.Current price is: $47.50.

ATA gives the user the ability to make adjustments to either the windage or elevation without removing the caps on the Aimpoint T1/H1/T2, or Comp M5.

  • Consists of a pair of 17-4 SS billet machined cap with internal O ring, and a 17-4 SS rotating disc with an externally accessible top slot.
  • To make adjustments to either the windage or elevation, the user uses the rim of a cartridge (.223, .308, .45 ACP, and 9mm were tested) or a coin to rotate the externally accessible disc of the ATA.
  • ATA’s caps are serrated to assist in its installation.
  • ATA is billet machined in 17-4 stainless steel, and QPQ treated.
View product
-5%
Add to compare

Forward Controls Design CNF Castle Nut

Out of stock

$19.76 – $24.70

The TDP spec castle nut is a simple and robust fastener that is almost perfect for the job it’s tasked to perform. Over the years, FCD has consistently come up with two minor gripes, first is its staking notches seem rather shallow and short, second is many don’t enjoy using the castle nut’s wrench notches as serrations (fingers invariably find their way to these sharp cutouts) to rotate it towards to the endplate while installing it.

  • Staking notches angle changed from 45 to 30 degrees, this results in longer (25% longer than TDP spec) and deeper notches than found on TDP castle nuts.
  • Number of staking notches increased from 3 to 4, spaced equally on the CNF. The castle nut is to be staked in two places, we’re not advocating staking in more than two places, CNF’s 4 staking notches mean that, at all times, 3 will be visible and available for staking, it simply gives the user more staking location options.
  • Coarse serrations on the wrench side of the nut, a single-use feature to make it easier while rotating the CNF towards the endplate.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design RHF4 Picatinny Handguard – 11.5″

Out of stock

$269.85 – $296.40

RHF4 comes in two lengths, 11.5″ and 9.5″, it is a quad rail handguard based on the successful Centurion Arms C4 rail system. It is a lightweight, rugged, 2-piece free float rail that provides a continuous 12 o’clock rail when installed on the upper receiver. Like the C4 system, RHF4 is a rigid rail that clamps to a standard barrel nut on all AR15, M4, and M16-type weapons systems. This design allows the installation of the rail on an upper assembly without removing the front sight post or permanently attached muzzle devices.

  • Material: 6061 T6
  • Finish: Type 3 hard coat anodized
  • Weight: 12.40 with screws—1.1oz more with standard barrel nut
  • Length: 11.5″
  • Width: 2.1in
  • Height: 2.38
  • Inside diameter: 1.37
  • Rails: 1913 spec rail
  • Fasteners: grade 8 bolts phosphate finished
  • Made in the USA
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design RHF4 Picatinny Handguard – 9.5″

In stock

$250.85 – $291.60

RHF4 comes in two lengths, 11.5″ and 9.5″, it is a quad rail handguard based on the successful Centurion Arms C4 rail system. It is a lightweight, rugged, 2-piece free float rail that provides a continuous 12 o’clock rail when installed on the upper receiver. Like the C4 system, RHF4 is a rigid rail that clamps to a standard barrel nut on all AR15, M4, and M16-type weapons systems. This design allows the installation of the rail on an upper assembly without removing the front sight post or permanently attached muzzle devices.

  • Material: 6061 T6
  • Finish: Type 3 hard coat anodized
  • Weight: 10.5oz with screws—1.1oz more with standard barrel nut
  • Length: 9.5″
  • Width: 2.1in
  • Height: 2.38
  • Inside diameter: 1.37
  • Rails: 1913 spec rail
  • Fasteners: grade 8 bolts phosphate finished
  • Made in the USA
Select options This product has multiple variants. The options may be chosen on the product page