Forward Controls Design

-5%
Add to compare

Forward Controls Design SBCG Bolt Carrier Group – Dimpled

Out of stock

$213.75 – $261.75

SBCG-P (Secure staking, slick side BCG, Manganese Phosphate) is the phosphated version of the original SBCG, which is NP3 coated.

  • SBCG bolts are manufactured from Carpenter 158® Steel. Each Bolt is HP/MPI tested and inspected. Each bolt is shot peened and comes with a Sprinco heavy extractor spring and black spring insert.
  • Shot Peened
  • Sprinco 5-Coil Heavy Duty Extractor Spring
  • Black Insert
  • 100% HPT & MPI
  • SBCG carriers are 8620 steel and machined to USGI specifications. The M16/M4 carrier includes a mil-spec gas key. The gas key is heat treated per TDP specifications and NP3 coated. The gas key is secured to the carrier via OCKS (Optimized Carrier Key Screws), torqued to spec values, and properly staked.
  • Manganese phosphate coated.
Select options This product has multiple variants. The options may be chosen on the product page
-12%
Add to compare

Forward Control Design LMC Magazine Catch

Out of stock

Original price was: $35.00.Current price is: $30.73.

LMC (Low profile, duty, Magazine Catch) is a non-ambidextrous magazine catch for AR15/M16 and is centered around mitigating accidental/unintended magazine drops.

  • Note LMC was not designed for large-frame ARs, do not use LMC on 308 ARs.
  • 0.01″ longer catch (LMC’s 0.06″ vs. TDP’s 0.05″ length) that engages the magazine’s catch cutout window.
  • Shorter (by 1 full turn of the magazine catch) shaft that lowers the installed height of TDP spec magazine release button on the right side of the lower.
  • Winterized design to mitigate water pooling in wet and freezing temperatures.
  • Billet machined in 4140, heat treated, black nitride coated.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design OPF-M17/M18 Sig P320 Plate – ACRO, Rear Sight Dovetail

Out of stock

Original price was: $78.00.Current price is: $74.10.

OPF-G, ACRO, RSD is a drop in adapter for superb Aimpoint ACRO sights. OPF-M17.

  • ACRO, RSD is compatible with MIL-issued M17/M18.
  • Material: Machined in 4140 steel
  • Finish: Black oxide coated
  • Includes two 3/32 Allen screws (torque value: 12 to 14 in·lb), a 3/32 Allen key, and a packet of VC-3.
  • Proudly designed and made in the USA.
View product
-5%
Add to compare

Forward Controls Design OPF-M17/M18 Sig P320 Mounting Plate – ACRO

Out of stock

Original price was: $72.50.Current price is: $68.87.

OPF-G, ACRO is a drop in adapter for superb Aimpoint ACRO sights. Compatible Slides:

  • Civilian M17/M18
  • Compact
  • XCompact
  • Legion
  • Romeo1 Pro Cut
  • DPP Pro Cut
  • Pro Cut
  • AXG Cut
View product
-14%
Add to compare

Forward Controls Design CBW Combination Barrel Nut Wrench

Out of stock

Original price was: $40.00.Current price is: $34.39.
View product
Add to compare

Forward Controls Design MCF M-LOK Rail Cover – Long

Out of stock

$29.02

MCF (MLOK Cover, Forward Controls) is a collaboration between Railscales and Forward Controls Design.

  • Features an AA surface (All Angles, or dimpled) pattern.
  • Material: Machined in G10.
  • Width: 0.600″.
  • Thickness: 0.125″.
  • Length: Long 4.7″ (3 MLOK slits).
  • Weight: Long .48 oz per panel / Short .48 oz per panel.
  • Hardware: 416 stainless nuts.
  • 3/32 Allen key required (not included).
  • Torque value: 17 in/lb.
View product
-5%
Add to compare

Forward Controls Design ASF Ambidextrous Selector – Standard/Short

In stock

Original price was: $83.00.Current price is: $78.85.

ASF is a short-throw semi-auto selector with standard (non-offset) levers. The ASF comes in two models, giving the end-user an option between a 50-degree rotation and a 90-degree rotation for FIRE/SEMI.

  • ASF centers are billet machined in 8620, heat-treated, and black nitrided.
  • Levers are billet machined in 8620 and black nitrided.
  • ASF is a collaboration with Sons of Liberty Gunworks.
  • ASF is shipped with a selector spring.
  • Made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design ACF Ambidextrous Charging Handle (.223/5.56)

Out of stock

$114.00 – $120.37

The design objective for the AFC is a stronger, more durable ambidextrous charging handle that can withstand repeated mortaring and a better means of deflecting gas and debris from the shooter’s face and eyes when shooting with a sound suppressor.

  • Material: Machined from 7075 aluminum.
  • Finish: Type III hard coat anodized.
  • Significantly taller/thicker than the TDP design.
  • “Constant Motion” latch on either side of the T handle.
  • A taller and better gas deflection fence.
  • Made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design RHF M-LOK Handguard – 11.5″

Out of stock

Original price was: $200.00.Current price is: $190.00.

RHF (Railed Handguard, Forward Controls) is based on the superb CMT UHPR Mod2, with full-length 1913 rails at 12 o’clock, and MLOK at 3, 6, and 9 o’clock.

  • Machined from 6000 series extruded aluminum.
  • Barrel nut machined from 7075 aluminum.
  • Type 3 anodized
  • Weight: 9.25 oz.
  • Barrel nut torque: milspec 40-70ft/lbs.
  • Rail clamp screws torque: 45 inc/lbs.
View product
-17%
Add to compare

Forward Controls Design Stoner 63 Style Comp / Flash Hider (1/2×28)

Out of stock

Original price was: $50.00.Current price is: $41.71.

Threaded for 1/2×28, precision machined from solid 4140 steel bar stock and black nitrided, it is probably the finest A2 style comp/flash suppressor ever produced.

  • Material: 4140 steel bar.
  • Finish: Black nitride.
  • Provides 15 to 20% better muzzle rise compensation than the A2.
  • A crush washer is included.
  • Made in the USA.
View product
-21%
Add to compare

Forward Controls Design ACF Ambidextrous Charging Handle (.223/5.56) – BLEMISHED

Out of stock

Original price was: $85.00.Current price is: $67.32.

Note: These ACFs are BLEMISHED, the bottom of the ACF is machined a bit unevenly. The blemish has zero bearings on functionality and is invisible once installed.

The design objective for the AFC is a stronger, more durable ambidextrous charging handle that can withstand repeated mortaring and a better means of deflecting gas and debris from the shooter’s face and eyes when shooting with a sound suppressor.

  • Material: Machined from 7075 aluminum.
  • Finish: Type III hard coat anodized.
  • Significantly taller/thicker than the TDP design.
  • “Constant Motion” latch on either side of the T handle.
  • A taller and better gas deflection fence.
  • Made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
Add to compare

Forward Controls Design RE5F 9 Position A5 Compatible Receiver Extension

Out of stock

$60.00

RE5F is a 9 position receiver extension (RE), it is also compatible with Vltor’s splendid A5.

  • Material: Impact extruded 7075 aluminum with rolled threads.
  • Finish: Black anodize.
  • The interior is dry film lubed.
  • The body diameter is milspec (compatible with all milspec carbine stocks).
  • Extra drain holes to better and more quickly drain water inside the RE.
  • Softened sharp corners.
  • Collaboration with SOLGW and is identical to Sons of Liberty Gunworks Loyal 9 A5 RE.
  • 308 AR-compatible.
View product
-24%
Add to compare

Forward Controls Design EPC Ejection Port Cover

In stock

$38.00 – $47.80

EPC (Ejection Port Cover) is based on TDP dimensions, with thoughtful Forward Control touches, and incorporates features FCD thinks many will find useful.

  • Two tabs allowing the EPC to rest on the upper at a greater angle when it’s in the down/open position.
  • Shallow circular depressions on the side of the EPC provide texture tactile feedback to one’s finger.
  • Material: Billet machined from 7075 aluminum.
  • Finish: Hard coat Type III anodized.
  • EPC is compatible with TDP spec upper receivers.
  • Weight: 0.30oz.
  • Proudly designed and made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-12%
Add to compare

Forward Controls Design RHF M-LOK Handguard – 6.7″

Out of stock

Original price was: $175.00.Current price is: $154.51.

RHF (Railed Handguard, Forward Controls) is based on the superb CMT UHPR Mod2, with full-length 1913 rails at 12 o’clock, and MLOK at 3, 6, and 9 o’clock.

  • Machined from 6000 series extruded aluminum.
  • Barrel nut machined from 7075 aluminum.
  • Type 3 anodized
  • Weight: 7.5oz
  • Barrel nut torque: milspec 40-70ft/lbs.
  • Rail clamp screws torque: 45 inc/lbs.
View product
-12%
Add to compare

Forward Controls Design RHF M-LOK Handguard – 13.7″

Out of stock

Original price was: $205.00.Current price is: $180.12.

RHF (Railed Handguard, Forward Controls) is based on the superb CMT UHPR Mod2, with full-length 1913 rails at 12 o’clock, and MLOK at 3, 6, and 9 o’clock.

  • Machined from 6000 series extruded aluminum.
  • Barrel nut machined from 7075 aluminum.
  • Type 3 anodized
  • Weight: 11.51 oz
  • Barrel nut torque: milspec 40-70ft/lbs.
  • Rail clamp screws torque: 45 inc/lbs.
View product
-23%
Add to compare

Forward Controls Design Trigger Guard – Standard

In stock

$19.20 – $25.00

TGF (Trigger Guard, Forward Controls) is designed for use with TDP spec forged lower receivers, and fills the gap forward of the pistol grip, between the trigger guard “ears”.

  • Material: 7075 aluminum.
  • Finish: Anodized.
  • Front set screw is flush with the receiver and doesn’t protrude.
  • Canted front edge to make rocking the magazine into the mag well easier.
  • Trigger guard roll pin and set screw (for the front) are included.
  • A 1/16 Allen wrench is required (not included).
  • Proudly designed and made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design OPF-G Glock MOS Mounting Plate – DPP

Out of stock

Original price was: $72.50.Current price is: $68.87.

OPF-G, DPP (Optics Platform, Forward Controls, Delta Point Pro) uses the same proven design of the OPF-G, RMR to keep the Delta Point Pro immobile, the simplest and most effective way to prevent sight-to-plate mounting screws from loosening and shearing.

  • Billet machined in 4140.
  • Heat treated and black nitride coated.
  • Torque Value plate to slide: 13in/lb.
  • Torque Value sight to plate: 25in/lb.
  • Proudly designed and made in the USA.
View product
Add to compare

Forward Controls Design SCP Carrier Cam Pin – Dimpled Witness Mark, NP3

Out of stock

$17.56

SCP features a machined dimple on one side of the carrier cam pin, so the user can always reinstall the cam pin on the carrier in the same orientation.

  • Dimple ensures consistent installation.
  • Durable NP3 finish.
  • Reduces wear on cam pin and bolt.
View product
-5%
Add to compare

Forward Controls Design ABC/R v3 Augmented Bolt Catch – Dimpled

In stock

Original price was: $62.00.Current price is: $58.90.

The ABC/R is an angled paddle that makes it easier for the palm or thumb to access. FB (forward biased) is for right-hand users who wrap their left hand around the magazine well and use their left thumb to press the bolt catch’s upper paddle. The FB version has the upper-paddle shifted to the muzzle end to facilitate this reloading method.

  • Machined from billet 8620 alloy steel.
  • Heat-treated with black DLC finish.
  • Proudly designed and made in the USA.
  • Limited to one (1) per customer due to very high demand.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design ABC/R v3 Augmented Bolt Catch – Serrated

In stock

Original price was: $62.00.Current price is: $58.90.

The ABC/R is an angled paddle that makes it easier for the palm or thumb to access.

  • Machined from billet 8620 alloy steel.
  • Heat-treated with DLC finish.
  • Proudly designed and made in the USA.
  • Limited to one (1) per customer due to very high demand.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design OPF-G Glock MOS Mounting Plate – ACRO

Out of stock

Original price was: $72.50.Current price is: $68.87.

The OPF-G-ACRO is the perfect choice for installing the ACRO on your Glock MOS pistol slide. It is identical to the Tangodown AAM-01. FCD is proud to rebrand the Tangodown optic plate because of its outstanding design.

  • Machined in 4140 steel.
  • Melonite Coating.
  • Proudly designed and made in the USA.
View product
Add to compare

Forward Controls Design SCP Carrier Cam Pin – Dimpled Witness Mark, Nitride

Out of stock

$13.33

SCP features a machined dimple on one side of the carrier cam pin, so the user can always reinstall the cam pin on the carrier in the same orientation.

  • Dimple ensures consistent installation.
  • Durable nitride finish.
  • Reduces wear on cam pin and bolt.
View product
Add to compare

Forward Controls Design EMR-HC Enhanced Mag Release Button – Blind Hole, Dimpled

Out of stock

$17.56

FCD’s EMR-HC is a mag release with a taller profile than the factory mag release and it increases the usable surface.

  • 0.04″ taller than the factory magazine release button.
  • Very effective all-angle dimples.
  • Made from 4140 steel.
  • QPQ coated.
View product
Add to compare

Forward Controls Design EMR-HC-S Enhanced Mag Release Button – Blind Hole, Serrated

Out of stock

$17.56

FCD’s EMR-HC is a mag release with a taller profile than the factory mag release and it increases the usable surface.

  • 0.04″ taller than the factory magazine release button.
  • Very effective horizontal serrations.
  • Made from 4140 steel.
  • QPQ coated.
View product
Add to compare

Forward Controls Design EMR-H-S Enhanced Mag Release Button – Milspec Hole, Serrated

Out of stock

$17.56

FCD’s EMR-H is a mag release that increases the usable surface area while retaining the same footprint as a factory mag release.

  • 0.02″ taller than the factory magazine release button.
  • Very effective horizontal serrations.
  • Machined from 4140 Steel.
  • QPQ coated.
  • Proudly made in the USA.
View product
Add to compare

Forward Controls Design EMR-H-AA Enhanced Mag Release Button – Milspec Hole, Dimpled

Out of stock

$17.56

FCD’s EMR-H is a mag release that increases the usable surface area while retaining the same footprint as a factory mag release.

  • 0.02″ taller than the factory magazine release button.
  • Very effective all-angle dimples.
  • Machined from 4140 Steel.
  • QPQ coated.
  • Proudly made in the USA.
View product
-5%
Add to compare

Forward Controls Design ASF Ambidextrous Selector – Q Lever, Standard/Short

Out of stock

Original price was: $83.00.Current price is: $78.85.

ASF was designed from the ground up to be a defense/duty/combat safety selector, its mission is quite aptly reflected by the way its levers are attached to the center, via a stainless steel roll pin.

  • Includes 1 short-throw lever and 1 standard lever.
  • ASF-50 is a short-throw rotate to 50 degrees.
  • ASF-90 is a conventional rotation to 90 degrees.
  • Centers are billet machined in 8620 and heat treated and black nitrided.
  • Levers are billet machined in 8620 and are black nitrided.
Select options This product has multiple variants. The options may be chosen on the product page
-20%
Add to compare

Forward Controls Design EMR Ambidextrous Mag Release – Serrated

Out of stock

Original price was: $70.00.Current price is: $56.34.

EMR-A is a long in development ambidextrous magazine release for .223 and .308 AR receivers. The placement of its lever is well thought out to closely mirror the magazine release button on the right side.

  • Made from CNC machined 4140 steel.
  • Black Nitride coated.
  • Lever 7075 aluminum and Type 3 hard coat anodized.
  • The roll pin has a shear strength of 800lbs.
  • Made in the USA.
View product
-5%
Add to compare

Forward Controls Design EMR Ambidextrous Mag Release – Dimpled

Out of stock

Original price was: $70.00.Current price is: $66.50.

EMR-A is a long in development ambidextrous magazine release for .223 and .308 AR receivers. The placement of its lever is well thought out to closely mirror the magazine release button on the right side.

  • Made from CNC machined 4140 steel.
  • Black Nitride coated.
  • Dimpled texture allows all angle resistance.
  • Lever 7075 aluminum and Type 3 hard coat anodized.
  • The roll pin has a shear strength of 800lbs.
  • Made in the USA.
View product
-5%
Add to compare

Forward Controls Design ESF End Plate – 3 Sockets

Out of stock

$57.00 – $62.70

ESF (End plate, Sling Adapter, Forward Controls Design) is a drop-in end plate replacement for the AR platform (both 223 and 308 specs) featuring 3 QD swivel sockets.

  • Machined from 4140 steel.
  • Weight: 1.1 oz.
  • 3 QD swivel sockets.
  • Made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-5%
Add to compare

Forward Controls Design ESF End Plate – 1 Socket

Out of stock

$42.75 – $48.45

ESF-H1 is a drop-in end plate replacement for the AR platform and has a single rear-facing QD swivel socket.

  • Machined from 4140 steel.
  • 1 QD swivel socket.
  • For AR-15/AR-10.
  • Socket has no limiters.
  • Made in the USA.
Select options This product has multiple variants. The options may be chosen on the product page
-12%
Add to compare

Forward Controls Design RHF M-LOK Handguard – 15″

Out of stock

Original price was: $215.00.Current price is: $188.66.

RHF (Railed Handguard, Forward Controls) is based on the superb CMT UHPR Mod2, with full-length 1913 rails at 12 o’clock, and MLOK at 3, 6, and 9 o’clock.

  • Machined from 6000 series extruded aluminum.
  • Barrel nut machined from 7075 aluminum.
  • Type 3 anodized
  • Weight: 12.35oz
  • Barrel nut torque: milspec 40-70ft/lbs.
  • Rail clamp screws torque: 45 inc/lbs.
Select options This product has multiple variants. The options may be chosen on the product page
Load more products
Loading...